Indirect addressing

Indirect addressing is a very powerful addressing mode which in many cases provides an exceptional level of flexibility. Indirect addressing is also the only way to access the extra 128 bytes of Internal RAM found on an 8052.

 Indirect addressing appears as follows:       MOV A, @R0

 This instruction causes the 8051 to analyze the value of the R0 register. The 8051 will then load the accumulator with the value from Internal RAM which is found at the address indicated by R0.
For example, lets say R0 holds the value 40h and Internal RAM address 40h holds the value 67h. When the above instruction is executed the 8051 will check the value of R0. Since R0 holds 40h the 8051 will get the value out of Internal RAM address 40h (which holds 67h) and store it in the Accumulator. Thus, the Accumulator ends up holding 67h.
Indirect addressing always refers to Internal RAM; it never refers to an SFR. Thus, in a prior example we mentioned that SFR 99h can be used to write a value to the serial port. Thus one may think that the following would be a valid solution to write the value 1 to the serial port:

MOV R0, #99h ;Load the address of the serial port
MOV @R0, #01h ;Send 01 to the serial port -- WRONG!!

This is not valid. Since indirect addressing always refers to Internal RAM these two instructions would write the value 01h to Internal RAM address 99h on an 8052. On an 8051 these two instructions would produce an undefined result since the 8051 only has 128 bytes of Internal RAM.

Comments

Post a Comment

Popular posts from this blog

General puprose registers in 8051.

Image
Well, in yesterday's podcast discussed on registers in 8051, two types of a register, general purpose registers are today's article all about. The general purpose registers are called as RAM memory in 8051. It has 128 bytes of memory for this general purpose registers. These general purpose registers are divided into 3 areas, those are  Banks. Bit addressable areas. scratchpad areas.                                     Let we discuss clearly, Banks    In this bank, 4 types of banks are there like  bank 0 bank 1 bank 2 bank 3 In each bank has 8 registers those are R0 to R7. All these general purpose registers are byte addressable registers. An image is shown in below for better understanding,                                     ...
Read more

TCON Special Function register.

Image
If a counter is programmed to be a timer, it will count the internal clock frequency of the 8051 oscillator 12d. As an example, if the crystal frequency 6 MHz, then the timer clock will have a frequency of 500kHz.   The timers may operate in any one of four modes that are determined by the mode bits. In that the timer control TCON it is a special function register. TCON:   Pin Description of TCON: Bit Symbol TCON Bit Function 7 TF1l Timer 1 Overflow flag. Set when timer rolls from all 1's to 0. Cleared when processor vectors to execute interrupt service routine located at program address 001Bh. 6 TR1l Timer 1 run control bit. Set to 1 by a program to enable the timer to count; cleared to 0 by the program to halt timer. 5 TF0 l Timer 0 Overflow flag. Set when timer rolls from all 1's to 0. Cleared when processor vectors to execute interrupt service routine located at program address 000Bh. 4 TR0l Timer 0 run control bit. Set to 1 by a program to ...
Read more

TMOD Special Function Register.

TMOD register As we know there are 2 timer registers in 8051. Timer 0 and timer 1. Both of these registers use the same register called TMOD to set various timer operation modes. TMOD is an 8-bit register, in which lower 4 bits are for Timer 0 and upper 4 bits are for Timer 1. See table below. MSB ---- LSB GATE C/T M1 M0 GATE C/T M1 M0 TIMER 1 TIMER 0 Bit Description: Bit TMOD Bit Function 7 Gate -- OR gate enable bit which controls RUN/STOP of timer 1. Set to 1 by the program to enable the timer to run if bit TR1 in TCON is set and the signal on external interrupt is high. Cleared to 0 by the program to enable time to run if bit TR1 is set. 6 C/ T  -- Set to 1 by the program to make timer 1 act as a counter by counting pulses from external input pins 3.5. Cleared to zero by the program to make timer act as a timer by counting internal frequency. 5 M1 -- Timer/counter operating mode select bit 1. Set/cleared by the...
Read more